estuary owners
+8
Capt. Larry M
Mike B
Bob M
farrukh ashraf
Chris S.
Kevin Stupp
Davey Welsh
Jim Donofrio
12 posters
Page 2 of 2
Page 2 of 2 • 1, 2
10x13
1999 2 stroke Johnson longshaft with a 10 x 13 3 blade prop.
Mike B- Regular Gunner
- Posts : 87
Join date : 2011-12-10
Location : Barnegat Bay
prop
Mike you are way over wheeled you need a 9.25/11 on that motor thats way you are not making RPM they are available on ebay also brand new
Re: estuary owners
9.25 x 11 prop.......any type aluminum, SS anny particular manufacturer?
Mike B- Regular Gunner
- Posts : 87
Join date : 2011-12-10
Location : Barnegat Bay
Re: estuary owners
Jim Donofrio wrote:Mike you could go down to a 10 inch I have one try it and see
It may run perfect witha ten
It has a 10 x 13 now. what would your 10 be?
Mike B- Regular Gunner
- Posts : 87
Join date : 2011-12-10
Location : Barnegat Bay
Re: estuary owners
Mike Braden wrote:Jim Donofrio wrote:Mike you could go down to a 10 inch I have one try it and see
It may run perfect witha ten
It has a 10 x 13 now. what would your 10 be?
My bad maybe a 9.25 x 10?????
Mike B- Regular Gunner
- Posts : 87
Join date : 2011-12-10
Location : Barnegat Bay
Re: estuary owners
Jim Donofrio wrote:yes you have way too much wheel take my ten and try it gurantee she runs like a bastard
I'm usually kin to the phrase "runs like a raped ape"
Mike B- Regular Gunner
- Posts : 87
Join date : 2011-12-10
Location : Barnegat Bay
Re: estuary owners
Mike, my buddy runs a 14 w a 25 merc 2 stroke. A dolfin made all the difference for him. The 14 has a slight rocker to the hull that I think causes it to push. The dolfin seems to counter act the rocker. Rated at the factory 15hp. go figure
Phil
Phil
Phil Eager- FNG
- Posts : 9
Join date : 2012-01-23
Re: estuary owners
Phil Eager wrote:Mike, my buddy runs a 14 w a 25 merc 2 stroke. A dolfin made all the difference for him. The 14 has a slight rocker to the hull that I think causes it to push. The dolfin seems to counter act the rocker. Rated at the factory 15hp. go figure
Phil
I thought of that too Phil but I figured the prop may be the culprit as well. My friend has a TDB with a 25 and his boat gets up and goes with out the Dolfin. He is going to check into his prop size as well.
Mike B- Regular Gunner
- Posts : 87
Join date : 2011-12-10
Location : Barnegat Bay
PROPS FOR A MARINER 15HP
Hey guys. I am wondering what pitch prop to use on my 15hp Mariner. The motor is about 15 years old but still runs fine. Anyone out there use Mariners?
Thanks,
Russell
Thanks,
Russell
Russell Vrhovac- Regular Gunner
- Posts : 144
Join date : 2012-01-11
Location : Chesapeake, VA
Re: estuary owners
Russell Vrhovac wrote:Hey guys. I am wondering what pitch prop to use on my 15hp Mariner. The motor is about 15 years old but still runs fine. Anyone out there use Mariners?
Thanks,
Russell
What kinda boat do you have the 15hp on? is the prop on it not moving the boat very well? Does it bog or over rev. I would see how it does with whatever prop is on it now and go from there. It may be perfect the way it is. Every boat will act different. Going with what you have now and seeing how it does is your best bet. Then you can go up or down in pitch if its bogging or over reving. Good luck!
Chris S.- Moderator
- Posts : 210
Join date : 2011-12-10
Location : south jersey
Estuary and Prop size
Hey I just found all of this and wanted to comment, I am no expert but I am running a 15hp Yamaha 2 stroke on my estuary with a high thrust Yamaha 9.3/4 X 6 1/2 and it has doubled the speed of the boat.
rracioppi- FNG
- Posts : 1
Join date : 2012-12-03
Re: estuary owners
Hey Jim..I have a DH-15 with a 25 horse 4 stroke pushing it..I'm running the stock prop, anything i can do to it...seems like it boggs at times with the fat boys init...besides going up to a 30 horse motor?
Rusty Black- Regular Gunner
- Posts : 130
Join date : 2012-01-12
Location : Hunting PA&NJ
Page 2 of 2 • 1, 2
Similar topics
» 2002 Estuary rebuild DONE!!!!
» 12' Estuary...Canvas coamming instaled
» Estuary Hull Mold // Garvey Hull Mold
» 12' Estuary...Canvas coamming instaled
» Estuary Hull Mold // Garvey Hull Mold
Page 2 of 2
Permissions in this forum:
You cannot reply to topics in this forum
|
|